Enabling Jumbo Frames on virtual switches
search cancel

Enabling Jumbo Frames on virtual switches

book

Article ID: 324494

calendar_today

Updated On:

Products

VMware vSphere ESXi

Issue/Introduction

This article provides information about enabling Jumbo Frames in a virtual switch.

Note: If vmkernels on a virtual switch are set to 9000 MTU, the virtual switch must also be set to 9000 MTU. However, if the virtual switch is set to 9000 MTU, it is not a requirement to set all vmkernels on the virtual switch to 9000 MTU. 


Symptoms:

 



Resolution

To enable Jumbo frames in a virtual switch, follow these steps:
    1. Globally, so that all portgroups and ports in the virtual switch have Jumbo Frames enabled.
    2. At the VMkernel port, so that only specific VMkernels are configured with Jumbo Frames (usually configured for storage or vMotion).
    Note: Ensure that your network card, physical switches, and storage devices support Jumbo Frames before configuring.
     

    Enabling Jumbo Frames for all portgroups or ports of a vDS

    You can configure the MTU value of a vDS switch so that all portgroups and ports use Jumbo Frames.
     
    To configure Jumbo Frames on a vDS in vSphere Web Client:
    1. Browse to a distributed switch in the vSphere Web Client navigator.
    2. Click the Actions tab, and click Settings > Edit Settings.
    3. Click Advanced and set the MTU property to a value greater than 1500 bytes.
      • You cannot set the MTU size to a value greater than 9000 bytes.
      • When changing the MTU size in a vDS, the attached uplinks (physical NICs) are brought down and up again. This causes a short network outage for virtual machines and/or services that are using the uplinks.
    4. Click OK.

    Enabling Jumbo Frames for all portgroups or ports of a vSS

    You can configure the MTU value of a vSS switch so that all portgroups and ports use Jumbo Frames.
     
    To configure Jumbo Frames on a vSS in vSphere Web Client:
    1. In the vSphere Web Client, navigate to the host.
    2. On the Configure tab, click Virtual Switches.
    3. Navigate to the virtual switch, then click Edit.
    4. Set the MTU value to 9000.

      Note: You can increase the MTU size up to 9000 bytes.

    Enabling Jumbo Frames on a VMkernel port from the vCenter Server

    To enable Jumbo Frames on a VMkernel port using the vSphere Web Client in vCenter Server:
    1. In the vSphere Web Client, navigate to the host.
    2. On the Configure tab, click VMkernel Adapters.
    3. Click Edit.
    4. Set the MTU value to 9000.

      Note: You can increase the MTU size up to 9000 bytes.


    Additional Information

    For more information on configuring Jumbo frames, see iSCSI and Jumbo Frames configuration on ESX/ESXi (1007654). Jumbo frames must be configured similarly across the board on both virtual and physical infrastructure, such as vSwitch, Portgroups, VMkernel, and physical switch port.

    For more information on troubleshooting host Jumbo Frame issues, as well as how to test that Jumbo Frame connectivity is working as it should be, see Troubleshooting disk latency when using Jumbo Frames with iSCSI or NFS datastores (2002197).

    iSCSI and Jumbo Frames configuration on VMware ESXi/ESX
    Troubleshooting disk latency when using Jumbo Frames with iSCSI or NFS datastores
    仮想分散スイッチでのジャンボ フレームの有効化
    在虚拟分布式交换机上启用巨型帧
    vmkping コマンドを使用した VMkernel ネットワーク接続のテスト

    Impact/Risks:
    When changing the MTU size on a vDS, the attached physical NICs are brought down and up again instantly. This causes a very brief network outage on the vDS.

    Powered by Wolken Software